ABOUT US

What is a surge arrester and how does it protect your electrical system?


Release time:

2026-11-16

Article overview

This guide covers the definition, working principle, classification, standards, selection criteria, and installation practices for surge arresters — with specific reference to South African electrical codes, local ZAR pricing benchmarks, and IEC 60099 compliance requirements.

What is a surge arrester?

A surge arrester is an overvoltage protection device connected between a conductor and earth that clamps and diverts transient voltage spikes away from equipment before they can cause damage. In plain terms, it acts as a pressure-relief valve for your electrical system — when voltage rises dangerously above the rated level, the arrester opens a low-impedance path to earth and closes it again once normal conditions return.

The term is often used interchangeably with lightning arrester, surge protector, and surge protective device (SPD), though there are technical distinctions. A lightning arrester specifically handles impulses caused by direct or indirect lightning strikes, while the broader category of surge arrester also covers switching transients generated inside the network. For a detailed surge arrester overview, the foundational definitions are well-documented and worth reviewing before specifying any device.

Why South Africa's grid makes surge protection non-negotiable

South Africa's combination of frequent thunderstorms — particularly across Gauteng, Limpopo, and KwaZulu-Natal — and an aging transmission infrastructure creates one of the highest transient overvoltage risks on the continent. Load-shedding cycles also introduce switching surges every time circuits are re-energised. According to the South African Weather Service, the Highveld experiences over 70 thunderstorm days per year, making robust overvoltage protection not a luxury but a baseline engineering requirement.

Surge arrester vs. surge protector: understanding the difference

Many buyers confuse a household surge protector power strip with a true surge arrester. The former is a consumer-grade device rated for low-energy, low-voltage applications. A proper surge arrester — classified under IEC 60099 — is an engineered protection device rated for medium-voltage (MV) or high-voltage (HV) distribution and transmission systems. The distinction matters enormously when specifying equipment for industrial sites, substations, or Eskom-connected installations.

How does a surge arrester protect your electrical system?

A surge arrester protects your electrical system by continuously monitoring line voltage and triggering a controlled discharge path to earth the instant voltage exceeds a pre-set threshold, then restoring normal insulation once the transient passes. This two-stage response — clamp, then recover — happens in microseconds.

The voltage-clamping mechanism step by step

  1. Normal operating state: The arrester presents very high resistance — essentially an open circuit — and has no effect on line operation.
  2. Surge arrival: A lightning strike or switching event injects a transient voltage pulse onto the conductor. Voltage climbs steeply within microseconds.
  3. Conduction threshold reached: Once voltage exceeds the arrester's protective level, the internal Metal Oxide Varistor (MOV) stack dramatically reduces its resistance.
  4. Energy discharge: Surge current is redirected through the arrester body down the earth conductor, bypassing sensitive equipment entirely.
  5. Recovery: As the transient dissipates and voltage returns to normal, the MOV resistance rises again, the arrester returns to standby mode, and the system continues operating without interruption.

Think of it like a pressure-relief valve on a boiler — it opens under excess pressure, releases safely, and reseats automatically. The arrester does the same with electrical energy, absorbing and redirecting harmful impulses before they reach transformers, switchgear, or end-user equipment.

What happens without surge protection?

Without a properly rated surge arrester, a single lightning-induced transient can puncture transformer winding insulation, destroy motor windings, corrupt industrial control systems, and cause fires. In 2026, replacement costs for a medium-voltage distribution transformer in South Africa range from R180,000 to over R600,000 — not counting downtime losses. The arrester that could have prevented the failure typically costs a fraction of that figure.

Diagram showing surge arrester installation on a medium-voltage distribution line, with current flow paths during a lightning strike event and earthing conductor connected to ground

Types of surge arresters: Type 1, Type 2, and Type 3 explained

IEC 60099 and the harmonised SANS standards classify surge protective devices into three types based on their energy-handling capability and installation position. Choosing the wrong type is one of the most common — and costly — mistakes made during specification.

Type 1, Type 2, and Type 3 comparison table

Parameter Type 1 (Class I) Type 2 (Class II) Type 3 (Class III)
Typical installation point Main distribution board / LV entry Sub-distribution boards Point-of-use / equipment terminals
Test impulse 10/350 µs (high energy) 8/20 µs 8/20 µs (low energy)
Impulse current (Iimp) 12.5 kA – 25 kA 5 kA – 20 kA 1 kA – 3 kA
Voltage protection level (Up) ≤ 4 kV ≤ 2.5 kV ≤ 1.5 kV
Typical ZAR cost (2026) R2,500 – R8,000 R600 – R2,500 R120 – R600
Suitable for direct lightning attachment? Yes No No

Industry consensus is that a layered or "coordinated" protection strategy — combining Type 1 at the service entrance, Type 2 at sub-boards, and Type 3 at sensitive equipment — delivers the most comprehensive transient voltage suppression. Using a Type 2 device alone at the meter board, while common in lower-budget installations, leaves residual surge energy that can still destroy VFDs, PLCs, and other sensitive electronics.

Distribution arresters vs. station class arresters

At medium and high voltage, the classification shifts. A distribution arrester is designed for 11 kV to 36 kV systems — typical of Eskom's local distribution networks and municipal reticulation. A station class arrester is built for substation environments operating at 66 kV and above, where energy-handling demands are orders of magnitude higher. Station class devices undergo far more rigorous testing under IEC 60099-4 and are significantly heavier and more expensive than their distribution counterparts.

Key components: Metal oxide varistors and beyond

The core of virtually every modern surge arrester is the Metal Oxide Varistor (MOV) — a non-linear resistive element whose resistance drops sharply when voltage exceeds a threshold. Understanding the MOV explains why today's gapless polymer arresters have largely replaced older silicon carbide gap-type devices.

How the MOV works

An MOV disc is composed primarily of zinc oxide (ZnO) granules with small additions of bismuth, cobalt, and manganese oxides sintered together. At normal operating voltage, grain boundaries within the material maintain high resistance — typically in the megaohm range. The moment voltage spikes, the junction barrier collapses and resistance drops to just a few ohms, allowing surge current to flow to earth. Once the transient clears, the material self-resets. This behaviour makes MOVs exceptionally well-suited as a transient voltage suppressor because they react without any mechanical moving parts or spark gaps.

Polymer vs. porcelain housing: what matters in the field

Historically, surge arresters used porcelain housings — robust but heavy and prone to explosive shattering during internal fault conditions. Modern high voltage arresters increasingly use silicone rubber polymer housings. Actual field experience with polymer arresters in South Africa's coastal environments (where salt-laden air accelerates surface tracking on porcelain) confirms that polymer units maintain better pollution performance over time. That said, certain MV applications in high-UV, high-ozone environments still benefit from glass or porcelain enclosures — so the choice is never entirely straightforward.

"Zinc oxide surge arresters have fundamentally changed transmission line protection — their superior energy absorption, self-restoring behaviour, and compact form factor have made spark-gap devices largely obsolete in modern substation design." — IEEE Working Group on Surge Arrester Applications, referenced in the understanding surge arresters technical bulletin.

Surge arrester standards — IEC 60099 and SANS compliance in South Africa

Compliance with the correct standard is not optional for South African installations — it is a legal and contractual requirement under the Occupational Health and Safety Act and Eskom's distribution code. The primary international framework is IEC 60099, which the South African Bureau of Standards (SABS) has adopted through the SANS 60099 series.

IEC 60099 series breakdown

The IEC 60099 standard family covers different arrester types and test requirements. For practitioners specifying equipment in South Africa, the most relevant parts are IEC 60099-4 (metal-oxide surge arresters without gaps for AC systems) and IEC 60099-5 (selection and application recommendations). The surge arrester standards published by IEC provide the definitive technical framework for testing, rating, and classifying these devices.

What SANS compliance means for procurement in South Africa

When procuring surge arresters for South African projects — whether for Eskom-connected MV networks or low-voltage commercial installations — buyers should request test certificates confirming SANS 60099-4 or SANS 61643-11 compliance. Products claiming compliance but lacking traceable third-party test documentation should be treated with caution. The earthing and bonding installation must also comply with SANS 10142-1 (the South African wiring code) to ensure the arrester discharge path is effective. Without a low-impedance earth electrode, even the best-specified arrester will fail to protect the system adequately.

How to select the right surge arrester for your application

Correct selection of a surge arrester depends on five parameters: system voltage, lightning protection level (LPL), installation location, the energy-handling requirement, and equipment sensitivity. Skipping any one of these factors leads to under- or over-specified protection.

Step-by-step selection process

  1. Determine the maximum continuous operating voltage (MCOV): The arrester's rated voltage must be equal to or greater than the highest sustained system voltage, including temporary overvoltages (TOV). For a standard South African 230 V / 400 V LV system, a Type 2 device rated at 275 V MCOV is the minimum.
  2. Establish the lightning protection zone (LPZ): Using IEC 62305 zones — LPZ 0 to LPZ 3 — identify where in the system each arrester will be installed. The transition from LPZ 0 to LPZ 1 (typically the service entrance) requires a Type 1 device.
  3. Select the nominal discharge current (In): For Type 2 devices, 20 kA (8/20 µs) is considered best practice for South African applications given the region's high keraunic level.
  4. Verify the voltage protection level (Up): Up must be below the impulse withstand voltage of the equipment being protected. Sensitive electronics (PLCs, VFDs, medical equipment) typically require Up ≤ 1.5 kV.
  5. Check housing suitability: For outdoor MV applications in coastal or high-pollution areas, specify polymer-housed arresters with IPX5 or better ingress protection and a suitable pollution class per IEC 60815.
  6. Confirm compliance documentation: Request SANS 60099-4 or SANS 61643-11 test certificates before finalising any purchase order.

Why over-specifying can be a problem too

Why do some installers default to the highest-rated device available? The assumption is that more protection is always better. In reality, an arrester with an excessively high voltage protection level (Up) relative to the equipment's withstand capability provides inadequate clamping — the device doesn't conduct until the voltage has already exceeded what the equipment can tolerate. Proper coordination, not brute-force ratings, is the engineering objective.

Installation best practices and common mistakes

Even a correctly specified surge arrester will fail to protect adequately if installed incorrectly. Field observations across South African industrial and commercial sites consistently reveal the same recurring errors — all preventable with proper planning.

Critical installation requirements

Lead length is the single biggest source of installation error. Every 1 metre of lead wire between the arrester terminal and the busbar adds approximately 1 µH of inductance, which under fast-rising surge currents (high di/dt) generates an additional voltage drop that reduces the arrester's effective clamping level. Best practice is to keep total lead length — input lead plus earth lead combined — below 0.5 m. Where this is geometrically impossible, a V-connection wiring arrangement minimises the effect.

The earth electrode must present an impedance of less than 10 ohms at the point of installation, per SANS 10142-1 recommendations. In rocky Highveld terrain, achieving this may require driven rod arrays or chemical earthing electrodes. Without a compliant earth, the arrester's discharge current has nowhere to go effectively, and the full surge energy transfers into the protected equipment — the exact outcome the device was meant to prevent.

Common mistakes and how to avoid them

Of course, there are situations where even a well-installed arrester reaches end-of-life prematurely — particularly in areas with repeated direct lightning attachment or where temporary overvoltages from MV earth faults persist for extended periods. Modern arresters include thermal runaway protection, but devices subjected to excessive cumulative energy stress beyond their rating will fail. Specifying an arrester with a higher energy class than the minimum required provides a valuable safety margin in high-risk locations.

Other frequently observed errors include: installing a Type 2 device at the main incomer when a Type 1 is required by the lightning protection system design; failing to bond the arrester earth terminal to the main earthing busbar (creating a potential difference during discharge); and neglecting periodic inspection — IEC 60099-5 recommends visual inspection at least annually and leakage current monitoring for MV station class devices every five years.

Frequently asked questions

Q: What is the difference between a surge arrester and a surge protective device (SPD)?

A: The terms are closely related but differ in scope. A surge arrester typically refers to medium- and high-voltage devices used in distribution and transmission systems, while a surge protective device (SPD) is the broader IEC category that includes low-voltage equipment. All surge arresters are SPDs, but not all SPDs are surge arresters — a plug-in power strip with MOV protection, for example, is an SPD but not a surge arrester in the technical sense.

Q: How often should surge arresters be replaced or inspected in South Africa?

A: IEC 60099-5 recommends annual visual inspection for all installations and leakage current monitoring every five years for MV station class units. In high-lightning-density areas such as the Highveld, more frequent inspection is advisable. Polymer-housed arresters showing surface tracking, cracking, or discolouration should be replaced immediately regardless of their rated service life.

Q: Can I use a Type 2 surge arrester at the main distribution board without a Type 1?

A: Only if no external lightning protection system (LPS) is installed on the structure and there is no overhead power line connection. Where an LPS exists or the supply enters via overhead conductors, IEC 60364-5-534 and SANS 10142-1 require a Type 1 device at the service entrance to handle the high-energy 10/350 µs lightning impulse that a Type 2 device is not rated to absorb.

Q: What does the IEC 60099 standard cover for surge arresters?

A: IEC 60099 is a multi-part standard covering the design, testing, classification, and application of surge arresters for AC systems. Part 4 addresses metal-oxide gapless arresters, Part 5 covers selection and application guidelines, and Part 8 deals with surge arresters for DC systems. South Africa adopts this framework through the SANS 60099 series, enforced on all Eskom-connected and COC-compliant installations.

Q: How do I know if my existing surge arrester is still functional?

A: Several indicators suggest an arrester may have degraded: visible housing cracks or tracking marks, a tripped thermal disconnect (found on many LV SPDs), elevated leakage current readings above manufacturer thresholds during routine monitoring, or a history of multiple nearby lightning events. When in doubt, a qualified electrician should perform a leakage current test or replace the unit — the cost of a new arrester is negligible compared to the equipment it guards.

Conclusion

A correctly specified and properly installed surge arrester is one of the most cost-effective investments in electrical system reliability — particularly in South Africa's high-keraunic environment. From understanding the difference between Type 1, Type 2, and Type 3 classifications, to ensuring earthing and bonding compliance under SANS 10142-1, every step of the selection and installation process directly determines how well your system withstands the next surge event. The coordination of a full lightning protection system with the right arrester tier at every voltage boundary is not over-engineering — it is simply sound electrical practice backed by decades of field evidence and IEC 60099 test data. When budgeting for your next project, factor in the full cost of non-protection: transformer replacement, downtime, and liability far outweigh the modest outlay for a compliant surge arrester stack.

Keywords:

Contact information

WhatsApp/Wechat:

Address:

No.336 Bai Xin Industry Zone, Chuiyan Minqing, Fuzhou, Fujian Porvince, China

 

Fa:

0086-591-87807600

Message

Please feel free to contact us with any questions. We’re here to help.

%{tishi_zhanwei}%

Copyright © Fuzhou Colmate Electric Co., Ltd.

Powered by :www.300.cn   SEO   Privacy Policy